PPT ON ARP AND RARP

CLICK HERE TO DOWNLOAD PPT ON ARP And RARP

ARP And RARP  Presentation Transcript

1.ARP and RARP
Understand the need for ARP
 Understand the cases in which ARP is used
 Understand the components and interactions in an ARP package
 Understand the need for RARP

2. ARP and RARP

3.Position of ARP and RARP in TCP/IP protocol suite

4.ARP
ARP associates an IP address with its physical address. On a typical physical network, such as a LAN, each device on a link is identified by a physical or station address that is usually imprinted on the NIC.

5.ARP operation

6.ARP packet

7.Encapsulation of ARP packet

8.Four cases using ARP

9.An ARP request is broadcast; an ARP reply is unicast.

10.A host with IP address 130.23.43.20 and physical address B2:34:55:10:22:10 has a packet to send to another host with IP address 130.23.43.25 and physical address A4:6E:F4:59:83:AB (which is unknown to the first host). The two hosts are on the same Ethernet network. Show the ARP request and reply packets encapsulated in Ethernet frames.

11.Solution Figure 7.7 shows the ARP request and reply packets. Note that the ARP data field in this case is 28 bytes, and that the individual addresses do not fit in the 4-byte boundary. That is why we do not show the regular 4-byte boundaries for these addresses. Also note that the IP addresses are shown in hexadecimal. For information on binary or hexadecimal notation see Appendix B.

12.Proxy ARP

13.ARP PACKAGE
In this section, we give an example of a simplified ARP software package to show the components and the relationships between the components. This ARP package involves five modules: a cache table, queues, an output module, an input module, and a cache-control module.

14.ARP components

15.Original cache table used for examples

16.The ARP output module receives an IP datagram (from the IP layer) with the destination address 114.5.7.89. It checks the cache table and finds that an entry exists for this destination with the RESOLVED state (R in the table). It extracts the hardware address, which is 457342ACAE32, and sends the packet and the address to the data link layer for transmission. The cache table remains the same.

17.Twenty seconds later, the ARP output module receives an IP datagram (from the IP layer) with the destination address 116.1.7.22. It checks the cache table and does not find this destination in the table. The module adds an entry to the table with the state PENDING and the Attempt value 1. It creates a new queue for this destination and enqueues the packet. It then sends an ARP request to the data link layer for this destination. The new cache table is shown in Table 7.2.

18.Updated cache table for Example 3

19.Fifteen seconds later, the ARP input module receives an ARP packet with target protocol (IP) address 188.11.8.71. The module checks the table and finds this address. It changes the state of the entry to RESOLVED and sets the time-out value to 900. The module then adds the target hardware address (E34573242ACA) to the entry. Now it accesses queue 18 and sends all the packets in this queue, one by one, to the data link layer. The new cache table is shown in Table 7.3.

20.Updated cache table for Example 4

21.Twenty-five seconds later, the cache-control module updates every entry. The time-out values for the first three resolved entries are decremented by 60. The time-out value for the last resolved entry is decremented by 25. The state of the next-to-the last entry is changed to FREE because the time-out is zero. For each of the three pending entries, the value of the attempts

22.Updated cache table for Example 5

23.RARP
RARP finds the logical address for a machine that only knows its physical address.
Packet Format
Encapsulation
RARP Server
Alternative Solutions to RARP

24.The RARP request packets are broadcast;
the RARP reply packets are unicast.

25.RARP operation

26.RARP packet

27.Encapsulation of RARP packet